ASTM F1869 Calcium Chloride Moisture Test Explained

18 Sep 2026
1 min read

What ASTM F1869 Actually Measures

ASTM F1869 is a laboratory-style field test that measures how much water vapor passes through the top surface of a concrete slab over a fixed time period. The result is reported as a Moisture Vapor Emission Rate, or MVER, expressed in pounds of water vapor per 1,000 square feet of slab surface per 24 hours. It is a rate of outward vapor movement at the surface, not a measurement of total moisture content inside the concrete.

That distinction matters more than most spec sheets suggest. F1869 tells you what’s leaving the slab at the moment of the test, at that specific location, under the specific temperature and humidity conditions present in the room at the time. It doesn’t tell you how much moisture is sitting two or three inches down, and it doesn’t predict what will happen six months from now if HVAC conditions change or a vapor barrier starts working differently under a warehouse floor loaded with racking. ASTM International’s F1869 standard (2016 edition, F1869-16a) defines the test method and calculation precisely, but the standard itself does not set pass/fail acceptance criteria. Those thresholds come from flooring adhesive and covering manufacturers, which is a point specifiers often miss.

How the Calcium Chloride Test Works, Step by Step

The test uses a small dish of anhydrous calcium chloride, a desiccant salt, sealed under a plastic dome on the slab surface for 60 to 72 hours. The dish is weighed before and after exposure, and the weight gain (moisture absorbed from the concrete) is converted into the MVER figure using a standard calculation defined in the ASTM method.

In practice, a technician cleans and conditions the test area, lets the slab acclimate to ambient service conditions for at least 48 hours before starting (temperature between 65°F and 85°F, relative humidity controlled, per the standard’s environmental requirements), then places the pre-weighed calcium chloride dish and seals the dome tightly to the surface. The test runs uninterrupted for 60 to 72 hours. At the end of the window, the dish is re-weighed immediately and the emission rate calculated. ASTM F1869 requires a minimum of three test locations for the first 1,000 square feet of slab, with one additional location for every 1,000 square feet beyond that, which means a 40,000 square foot distribution center floor needs a meaningful number of test points to represent the whole slab honestly.

Because the dome has to sit undisturbed for up to three days, F1869 requires the space to be closed to traffic and held at stable conditions for the full duration. That’s a real scheduling constraint on active job sites, and it’s one reason relative humidity probe testing under ASTM F2170 has become popular as a complementary or alternative method, since it doesn’t demand a three-day surface seal at each point.

Where F1869 Applies, and Where It Does Not

ASTM F1869 is written for bare, uncoated concrete slabs, on, above, or below grade, and its results become invalid the moment anything changes the slab’s surface chemistry or vapor path. Understanding these exclusions prevents wasted test cycles and mistaken conclusions about slab readiness.

The standard explicitly excludes several common conditions. It cannot be used on gypsum concrete or gypsum-based underlayments, because calcium chloride’s absorption behavior on gypsum doesn’t correlate to the same emission physics validated for portland cement concrete. It’s not valid on lightweight or structural lightweight aggregate concrete, where porosity and moisture retention behave differently than in normal-weight mixes. It cannot be run over any surface that has been sealed, coated, painted, or treated with a reactive penetrating sealer or densifier, since those treatments block or alter vapor transmission at the exact surface layer the test is measuring. It also cannot be run over patching compounds, skim coats, or leveling underlayments applied to the slab, for the same reason: the test measures what’s happening at the top quarter-inch to half-inch of material, and if that material isn’t the structural slab itself, the result describes the topping, not the concrete underneath.

Common mistake: Running F1869 on a slab that’s already had a curing compound, sealer, or patch applied invalidates the result under the standard. If the surface has been treated, F1869 is not the right test until that treatment is fully removed or accounted for in project documentation.

What the “3 lb / 1,000 sq ft / 24 hr” Threshold Really Means

The 3 pounds per 1,000 square feet per 24 hours figure is a widely cited flooring industry acceptance threshold, not a limit written into the ASTM F1869 standard itself. Many adhesive and resilient flooring manufacturers use it, or a lower number, as the maximum MVER they’ll warranty a product installation over.

This is where specifiers get into trouble. A slab testing at 3.2 lbs/1,000 sq ft/24 hr hasn’t “failed” any ASTM requirement, because F1869 has none. It may, however, fail the specific flooring manufacturer’s installation warranty threshold, which varies by product line, adhesive chemistry, and covering type. Vinyl composition tile, sheet vinyl, epoxy coatings, and wood flooring systems each carry their own manufacturer-set MVER and relative humidity limits, and those limits, not the ASTM standard, determine whether a given slab is ready for a given covering. Reading a moisture test report in isolation, without checking it against the actual flooring product’s written moisture tolerance, is one of the most common errors on commercial floor projects.

Why F1869 Can Miss Deeper Slab Moisture

F1869 measures vapor emission from roughly the top quarter to half inch of the slab surface. It says nothing directly about moisture conditions deeper in a 4-, 6-, or 8-inch slab, which is exactly where problems tend to originate on below-grade and slab-on-ground pours without an effective vapor retarder.

This limitation has real consequences. A slab can test acceptably at the surface under F1869 shortly after placement or after a period of dry ambient conditions, get a floor covering installed, and then experience moisture-related failure months later as internal moisture equilibrates and migrates upward, particularly in slabs poured over inadequate or damaged vapor barriers. ASTM F1869 also captures a single-point-in-time reading; it cannot describe how the slab’s internal moisture profile is trending. This is the core reason ACI 302.2R (American Concrete Institute’s guide for slabs receiving moisture-sensitive flooring) and most flooring manufacturer specifications now call for relative humidity testing under ASTM F2170 in addition to, or instead of, calcium chloride testing on projects with any elevated risk profile, since F2170 probes are inserted to 40% of slab depth (or 20% for slabs drying from both sides) and read internal conditions rather than surface emission alone.

How F1869 Fits with ASTM F2170 and ASTM F2659

These three ASTM methods answer different questions and aren’t interchangeable. F1869 measures surface vapor emission rate at one point in time; F2170 measures relative humidity inside the slab at a set depth using embedded probes; F2659 uses non-destructive electronic meters for quick, repeatable relative comparison scans across a large floor area, not absolute moisture values.

A common, defensible workflow on larger commercial jobs uses F2659 non-destructive scanning first, across the whole floor, to identify which zones read consistently wetter or drier relative to each other. That map then directs where to spend money on F1869 and F2170 testing, concentrated on the zones the scan flagged as elevated risk, rather than spreading a fixed test budget evenly across a slab that may have very uneven moisture conditions. F2170 gives a better picture of what’s happening deep in the slab and how it’s likely to trend, while F1869 remains useful for confirming surface emission against a specific flooring manufacturer’s warranty threshold at the time of installation. Treating any one of these three methods as a complete moisture diagnosis, on its own, is the mistake to avoid.

Method What It Measures Depth / Coverage Typical Duration
ASTM F1869 Surface vapor emission rate (MVER) Top ~1/4-1/2 inch, point locations 60-72 hours per test point
ASTM F2170 Relative humidity inside slab 20-40% of slab depth, probe locations Probes equilibrate ~24 hrs before reading; can remain in place for trending
ASTM F2659 Comparative moisture condition (non-destructive) Broad surface scan, whole-floor coverage Minutes per reading, rapid full-floor mapping

Is ASTM F1869 Changing? What Specifiers Should Know

ASTM F1869 has been revised multiple times since its original publication, with the current widely referenced edition being F1869-16a. ASTM standards go through periodic committee review (typically every five years or sooner if warranted), and specifiers should confirm they are referencing the current edition on any active project spec, since older editions can carry different environmental conditioning or reporting requirements.

Rather than being replaced outright, F1869 has increasingly been positioned as one tool within a broader moisture-testing protocol rather than a standalone acceptance test. Project specifications on larger commercial and industrial floors, especially distribution centers and manufacturing floors with moisture-sensitive coatings or flooring, increasingly call out F2170 relative humidity testing as the primary internal-moisture method, with F1869 retained for surface-specific manufacturer warranty compliance. Always check the specific edition cited in your project’s specification section before running or accepting any moisture test report.

Moisture Testing and Floor Flatness: Two Separate but Related QA Steps

Moisture testing and floor flatness testing answer different questions about slab readiness, and both matter on the same commercial floor project. Flatness (measured under ASTM E1155 as FF/FL numbers) determines whether the surface geometry meets tolerance for racking, robotics, or floor coverings; moisture testing determines whether the slab’s chemistry is dry enough to accept an adhesive, coating, or covering without failure risk.

A slab can be perfectly flat and still moisture-compromised, or moisture-ready and out of flatness tolerance for the racking system going in above it. On high-bay warehouse and distribution center projects where both flatness and moisture-sensitive floor coverings matter, an independent elevation survey is one of the core quality checkpoints IFTI performs, alongside moisture testing under F1869 and F2170, so project teams get an independent, measured answer on both fronts rather than relying on separate contractors’ self-reported numbers.

Planning slab testing on a warehouse, distribution center, or manufacturing floor project? IFTI provides an independent elevation survey alongside moisture testing services to give your team a full, third-party picture before flooring or racking installation begins.

Get a Free Consultation

Frequently Asked Questions

What does ASTM F1869 actually measure?

ASTM F1869 measures the Moisture Vapor Emission Rate (MVER) at the surface of a concrete slab, reported in pounds of water vapor per 1,000 square feet per 24 hours. It reflects vapor leaving the top quarter to half inch of the slab at the time of testing, not total moisture content throughout the slab.

Can ASTM F1869 be used on any concrete slab?

No. ASTM F1869 applies to bare, uncoated portland cement concrete slabs. It is not valid on gypsum concrete, lightweight aggregate concrete, coated or sealed surfaces, surfaces treated with reactive penetrants, or patching and leveling compounds, since these materials alter the vapor transmission the test is designed to measure.

What is the 3 lb/1,000 sq ft/24 hr threshold for?

This figure is a commonly cited flooring industry acceptance limit, not a requirement written into the ASTM F1869 standard itself. Flooring adhesive and covering manufacturers set their own MVER thresholds, often around this figure or lower, as a condition of product warranty coverage.

How long does an ASTM F1869 test take?

Each individual test requires a sealed dome placed on the slab surface for 60 to 72 hours, following at least 48 hours of ambient acclimation before the test begins. Multiple test locations are required per ASTM F1869 based on floor area, so total project turnaround depends on the number of points tested.

Why might a slab pass ASTM F1869 but still have moisture problems later?

F1869 measures only the slab surface at one point in time. It does not describe moisture deeper in the slab or how internal moisture is trending, so a slab can read acceptable at the surface while retaining elevated moisture below that later migrates upward and affects an installed floor covering.

How is ASTM F1869 different from ASTM F2170?

ASTM F1869 measures surface vapor emission using a calcium chloride dish over 60 to 72 hours. ASTM F2170 measures relative humidity inside the slab using probes inserted to 20 to 40 percent of slab depth. F2170 is generally considered more representative of internal slab moisture conditions and trending.

Is ASTM F1869 being replaced by newer test methods?

ASTM F1869 has not been withdrawn and remains an active, periodically revised standard, with F1869-16a as a widely referenced current edition. Rather than replacing it outright, many project specifications now pair F1869 with ASTM F2170 relative humidity testing for a more complete moisture assessment on higher-risk floors.

Sources

  • ASTM International, “ASTM F1869-16a Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride” (2016)
  • ASTM International, “ASTM F2170 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes” (2019)
  • ASTM International, “ASTM F2659 Standard Guide for Preliminary Evaluation of Comparative Moisture Condition of Concrete, Gypsum Cement and Other Floor Slabs and Screeds Using a Non-Destructive Electronic Moisture Meter” (2020)
  • American Concrete Institute, “ACI 302.2R Guide for Concrete Slabs that Receive Moisture-Sensitive Flooring Materials” (2006)

This article is for general informational purposes only and does not constitute engineering, legal, or product-specific advice. Flatness and levelness requirements and results vary by project, specification, and site conditions. Consult IFTI and refer to current ASTM (e.g., E1155, F1869, F2170) and ACI standards for project-specific guidance.

Cover of the IFTI Floor Flatness Standards PDF
Free PDF

Floor Flatness Standards

Fill in the form and download your free brochure today. Our team of flooring specialists has compiled years of experience and industry knowledge into this comprehensive guide. Benefit from our expertise to make the best decision for your property.

"*" indicates required fields

Name*

The PDF is on the next page. No sales sequence. Your details are used as described in our Privacy Policy.